嵌入式 ARM 平臺 libsoc 開發示例

發布人：toradex 時間：2019-05-14 來源：工程師

加入技術交流群
- 掃碼加入
  和技術大咖面對面交流
  海量資料庫查詢

By Toradex秦海

1). 簡介

在之前的一篇文章中已經介紹過如何基于嵌入式Linux部署libsoc支持，本文就繼續基于NXP IMX6平臺演示基于libsoc分別對GPIO，I2C，PWM以及SPI進行開發示例。

本文所演示的ARM平臺同樣來自于Toradex 基于NXP iMX6 ARM處理器的Apalis iMX6 ARM嵌入式平臺。

2. 準備

a). Apalis iMX6Q ARM核心版配合Apalis Evaluation Board載板，連接調試串口UART1（載板X29）到開發主機方便調試。更多關于Apalis iMX6配合Apalis Evaluation Board載板的說明請參考Datasheet和開發上手指南。

b). Apalis iMX6Q ARM核心版配合Ixora載板，連接調試串口UART1（載板X22）到開發主機方便調試。更多關于Apalis iMX6配合Ixora載板的說明請參考Datasheet和開發上手指南。

c). Apalis iMX6Q 安裝Toradex Linux BSP V2.8b5，系統中已經默認包含了本文測試所需要的libsoc相關庫支持，詳細安裝方法請參考這里，編譯libsoc相關demo所需要的SDK配置請參考簡介中提到的之前文章說明，本文不再贅述。

3). GPIO 測試示例

a). 基于Apalis Evaluation Board測試，硬件連接配置如下，基于C代碼的GPIO測試請參考這里，本文是基于libsoc來重新測試。

X4 GPIO05 <-> X34 SW5

X4 GPIO06 <-> X34 LED1

b). 源代碼請參考如下，實現功能就是按鍵交替點亮和關閉LED燈。

https://github.com/simonqin09/libsoc-examples/blob/master/gpiotest/gpiointtest.c

c). Makefile 請參考如下，直接下載的libsoc官方示例里面包含的Makefile需要進行一些修改，這里也將修改的patch附上。

./ Makefile

https://github.com/simonqin09/libsoc-examples/blob/master/gpiotest/Makefile

./ Patch file

https://github.com/simonqin09/libsoc-examples/blob/master/gpiotest/libsoc-examples_Makefile.patch

d). 測試運行結果如下：

-----------------------

root@apalis-imx6:~# ./gpiointtest

Waiting for interrupt. Press 'q' and 'Enter' at any time to exit

LED turns on

Interrupt occurred 1 times

LED turns off

Interrupt occurred 2 times

…

-----------------------

4). PWM 測試示例

a). 基于Apalis Evaluation Board測試，硬件連接配置如下, 基于C代碼的PWM測試請參考這里，本文是基于libsoc來重新測試。

X4 GPIO05 <-> X34 SW5

X4 PWM1 <-> X34 LED1

b). 源代碼和Makefile請參考如下，實現功能就是程序運行后，PWM以50%占空比輸出，通過按鍵讓PWM輸出占空比按照50%，75%，25% 交替調整。

https://github.com/simonqin09/libsoc-examples/blob/master/pwmtest/pwmtest.c

https://github.com/simonqin09/libsoc-examples/blob/master/pwmtest/Makefile

PWM2和PWM3也都可以測試，只是PWM3默認被ov5640_mipi驅動占用，需要修改device tree釋放。

d). 測試運行結果如下：

-----------------------

root@apalis-imx6:~# ./pwmtest

Waiting for interrupt. Press 'q' and 'Enter' at any time to exit

Interrupt occurred 1 times

PWM Duty set to 75%

Interrupt occurred 2 times

PWM Duty set to 25%

Interrupt occurred 3 times

PWM Duty set to 50%

Interrupt occurred 4 times

PWM Duty set to 75%

…

-----------------------

5). I2C 測試示例

a). 基于 Ixora 載板測試，針對載板上面連接到i2c-1的總線上面的EEPROM進行讀寫，基于C代碼的詳細測試文檔可以參考這里，本文重新基于libsoc代碼進行測試。

b). 源代碼和Makefile請參考如下，實現功能就是程序運行后，針對指定的page號碼寫入數據，然后再讀取后驗證是否讀寫一致。

I2ctest.c - https://github.com/simonqin09/libsoc-examples/blob/master/i2ctest/i2ctest.c

eeprom.c - https://github.com/simonqin09/libsoc-examples/blob/master/i2ctest/eeprom.c

eeprom.h - https://github.com/simonqin09/libsoc-examples/blob/master/i2ctest/eeprom.h

Makefile - https://github.com/simonqin09/libsoc-examples/blob/master/i2ctest/Makefile

d). 測試運行結果如下：

-----------------------

root@apalis-imx6:~# ./i2ctest 15

Writing to page starting at byte address: 0xf0

Waiting for data to be written

libsoc-i2c-debug: No such device or address

Waiting...

libsoc-i2c-debug: No such device or address

Waiting...

libsoc-i2c-debug: No such device or address

Waiting...

libsoc-i2c-debug: No such device or address

Waiting...

Data sucessfully written!

Reading page starting at byte address: 0xf0

data_write[0] = 0xf0 : data_read[0] = 0xf0 : Correct

data_write[1] = 0xf1 : data_read[1] = 0xf1 : Correct

data_write[2] = 0xf2 : data_read[2] = 0xf2 : Correct

data_write[3] = 0xf3 : data_read[3] = 0xf3 : Correct

data_write[4] = 0xf4 : data_read[4] = 0xf4 : Correct

data_write[5] = 0xf5 : data_read[5] = 0xf5 : Correct

data_write[6] = 0xf6 : data_read[6] = 0xf6 : Correct

data_write[7] = 0xf7 : data_read[7] = 0xf7 : Correct

data_write[8] = 0xf8 : data_read[8] = 0xf8 : Correct

data_write[9] = 0xf9 : data_read[9] = 0xf9 : Correct

data_write[10] = 0xfa : data_read[10] = 0xfa : Correct

data_write[11] = 0xfb : data_read[11] = 0xfb : Correct

data_write[12] = 0xfc : data_read[12] = 0xfc : Correct

data_write[13] = 0xfd : data_read[13] = 0xfd : Correct

data_write[14] = 0xfe : data_read[14] = 0xfe : Correct

data_write[15] = 0xff : data_read[15] = 0xff : Correct

-----------------------

6). SPI Master 測試示例

a). 基于Apalis Evaluation Board測試，需要配合Toradex另外一個基于NXP iMX7的平臺作為SPI slave進行共同測試，關于硬件連接和SPI slave的配制和相關代碼請參考下面文章，本文是基于libsoc來測試 SPI Master 端。

https://www.toradex.com/zh-cn/blog/nxp-imx7-m4-he-xin-spi-slave-ce-shi

b). 源代碼和Makefile請參考如下，實現功能就是程序運行后，通過Apalis iMX6 SPI0.0 向 SPI slave寫入一組隨機數據，然后再次通訊讀出剛才寫入的數據后確認讀寫是否一致。

spitest.c - https://github.com/simonqin09/libsoc-examples/blob/master/spitest/spitest.c

Makefile - https://github.com/simonqin09/libsoc-examples/blob/master/spitest/Makefile

d). 測試運行結果如下：

-----------------------

root@apalis-imx6:~# ./spitest

Start to transfer!

data_send[0] = 0xca : data_read[0] = 0xca : Correct

data_send[1] = 0x03 : data_read[1] = 0x03 : Correct

data_send[2] = 0x01 : data_read[2] = 0x01 : Correct

data_send[3] = 0x56 : data_read[3] = 0x56 : Correct