InfineonTLE983x智能汽車?yán)^電器驅(qū)動解決方案
英飛凌汽車電子生態(tài)圈
The TLE983x is a single chip solution that integrates a high performance 8-bit microcontroller derived from the established XC800 family with application specific power drivers, control and communication modules in an automotive qualified new Smart-Power Technology.
The TLE983x family concept offers scalability in terms of Flash memory sizes ranging from 36kB to 64kB with pin-compatible devices.
The TLE983x family was specifically designed to fit to a wide range of LIN-slave applications where a small package form factor and a minimum number of external components is essential.
TLE983x主要特性:
? High performance XC800 core
– compatible to standard 8051 core
– up to 40 MHz clock frequency
– two clocks per machine cycle architecture
– two data pointers
? On-chip memory
– 20, 32, 44 or 60 kByte + 4 kByte Flash for program code and data (4 kByte EEPROM emulation built-in)
– 512 Byte One Time Programmable Memory (OTP)
– 512 Byte 100 Time Programmable Memory (100TP)
– 256 Byte RAM
– 3 kByte XRAM
– BootROM for startup firmware and Flash routines
? Core logic supply at 1.5 V
? On-chip OSC and PLL for clock generation
– Loss of clock detection with fail safe mode for LSS, HSS and LIN
? Watchdog timer (WDT) with programmable window feature for refresh operation and warning prior to overflow
? General-purpose I/O Port (GPIO) with wake-up capability
? Multiplication/division unit (MDU) for arithmetic calculation
? Software libraries to support floating point and MDU calculations
? Five 16-Bit timers - Timer 0, Timer 1, Timer 2, Timer 21 and Timer 3
? Capture/compare unit for PWM signal generation (CCU6) and Hall Sensor measurement with Timer 12 and Timer 13
? Full duplex serial interface (UART) with LIN support
? Synchronous serial channel (SSC)
? On-chip debug support via 2-wire Device Access Port (DAP)
? LIN Bootstrap loader (LIN BSL)
? LIN transceiver compliant to LIN 1.3, LIN 2.0 and LIN 2.1
? 2 x Low Side Switches with clamping capability incl. PWM functionality, e.g. as relay driver
? 1 or 2 x High Side Switches with cyclic sense option and PWM functionality, e.g. for LED or powering of switches
? High Voltage Monitor Input pins for wake-up and with cyclic sense and analog measurement option
? Measurement unit with 10 channels, 8-Bit A/D Converter (ADC2) and data post processing
? 8 channels, 10-Bit A/D Converter (including battery voltage and supply voltage measurement) (ADC1)
? Single power supply from 3.0 V to 27 V
? Low-dropout voltage regulators (LDO)
? Dedicated 5 V voltage regulator for external loads (e.g. hall sensor)
? Programmable window watchdog (WDT1) with independent on-chip clock source
? Optional Operational amplifier for current sensing
? Power saving modes
– MCU slow-down mode
– Stop Mode
– Sleep Mode
– Cyclic wake-up and cyclic sense during Stop Mode and Sleep Mode
? Power-on and undervoltage/brownout reset generator
? Overtemperature protection
? Overcurrent protection with shutdown
? Supported by a full range of development tools including C compilers, macroassembler packages, emulators, evaluation boards, HLL debuggers, programming tools, software packages
? Temperature Range TJ: -40 °C up to 150 °C
? Package PG-VQFN-48
? Green package (RoHS compliant)
TLE983x主要優(yōu)勢:
??Complete system-on-chip (SoC) for ECU’s that communicate via LIN interface with main ECU
??High-voltage monitoring inputs for off-board switch control
??Highly flexible SoC through dedicated configuration registers for e.g. current and voltage settings as well as power saving modes
??High pin-count VQFN package with 7×7mm footprint enables space saving PCB designs
TLE983x汽車應(yīng)用:
??Window Lift
??Power Seats
??Sun Roof
??Fan/Blower Control
??Key Pad Interface
??Switch Panel Interface
圖1.TLE983x方框圖
圖2.TLE983x智能車窗升降模塊框圖
圖3.TLE983x評估板外形圖
圖4.TLE983x評估板電路圖(1)
圖5.TLE983x評估板電路圖(2)
TLE983x評估板材料清單:
圖6.TLE983x評估板PCB布局圖(1)
圖7.TLE983x評估板PCB布局圖(2)
圖8.TLE983x評估板PCB布局圖(3)
圖9.TLE983x評估板PCB布局圖(4)
圖10.TLE983x評估板PCB布局圖(5)
圖11.TLE983x評估板PCB布局圖(6)
圖12.TLE983x評估板PCB布局圖(7)
評論