基于MSP430的無線傳輸協議

初始化串口0，用于接收

void init_UART0(void)
{
UCTL0 &= ~SWRST;
UCTL0 |=CHAR;//0X10;
UBR00 = 0x03;
UBR10 = 0x00;
UMCTL0 = 0x4A;
UTCTL0 = SSEL0;//0X10;
ME1 |= UTXE0+URXE0 ; //enable the UART0
IE1 |=URXIE0;
P3SEL|=BIT4+BIT5;
P3DIR|=BIT4;
Clinet_Receive;
}

初始化串口1，用于發送

void init_UART1()
{
UCTL1 &= ~SWRST;
UCTL1 |=CHAR;//0X10;
UBR01 = 0x03;
UBR11 = 0x00;
UMCTL1 = 0x4A;
UTCTL1 = SSEL0; //
ME2 |= URXE1+UTXE1 ; //enable the UART1
IE2 |=URXIE1;
P3SEL|=BIT6+BIT7;
P3DIR|=BIT6+BIT7;
Host_Transmit;
}

初始化NRF401發射模塊

void init_NRF401_TR(void)
{
Host_PowerUp; //上電到發射狀態避免輻射和干擾
NRF401_CS;
delayms(5);
Host_Transmit; //設置串口無線模塊為發射模式
delayms(1); //延時4毫秒}

初始化NRF401接收模塊

void init_NRF401_RE(void)
{
Host_PowerUp; //上電到發射狀態避免輻射和干擾
NRF401_CS;
Host_Receive; //設置串口無線模塊為發射模式
delayms(5); //延時4毫秒}

發射模塊發送數據


__monitor void uart_H2C(unsigned char id,unsigned char cmd) //Host to Host transmit mode{

unsigned int crc=0;
unsigned char uart_Host_Tbuf[UART_BUF_SIZE]; //發送緩沖區
pro[0]=id;
pro[1]=cmd;
crc=cal_crc(pro,2); //計算校驗碼

uart_Host_Tbuf[0]=0x11; //先導字段，容易丟失
uart_Host_Tbuf[1]=0x55; //抗干擾字節
uart_Host_Tbuf[2]=0xAA; //幀開始字節
uart_Host_Tbuf[3]=id;
uart_Host_Tbuf[4]=cmd;
uart_Host_Tbuf[5]=(char)(crc/256); //循環冗余校驗高8位
uart_Host_Tbuf[6]=(char)(crc%256); //循環冗余校驗低8位
uart_Host_Tbuf[7]=0x77; //結束標志
uart_Host_Tnum=8; //發送幀長度，3個先導字節+2data＋2個校驗字節＋1個結束字
Host_Transmit;
delayms(5);
uart_Puts(uart_Host_Tbuf,uart_Host_Tnum,1); //發送數據}

通過實驗，發現在發送是延時片刻數據接收誤碼率低

__monitor void uart_Puts(unsigned char *str,unsigned char length,unsigned char uart_id)
//輸出多數據函數
{
while (length!=0)
{
if(uart_id==0)
uart0_putchar(*str++ ); //通過串口發送數據
else
{
uart1_putchar(*str++ ); //通過串口發送數據
delay(255);
}
length--;

}

}

void uart1_putchar(char c) //串口1發送一個字符{
TXBUF1 = c;
while((UTCTL1&0x01)==0);
}

接收通過中斷處理：
#pragma vector = UART0RX_VECTOR //下位機先進行數據接收__interrupt void Uart0rx_IRS(void)
{
int j=0;
_DINT();

if(flag0==0)
{
if(RXBUF0==0xFF)
{
flag0=1;
}
}
if(flag0==1)
{
if(RXBUF0==DeviceID) //設備碼驗證
{
flag1=1;
uart_Client_RPos=0;
}

}

if(flag0==1&&flag1==1)
{

uart_Client_Rbuf[uart_Client_RPos]=RXBUF0;
uart_Client_Rnum++; //接收數據計數器加1
uart_Client_RPos++; //移動接收緩沖區指針
if(uart_Client_Rbuf[uart_Client_RPos-1]==V) //幀結束字符
{
flag0=0;
flag1=0; //幀起始標志清除
for(;j //轉移接收到的數據
printf("UART0:%s",Data);


Clinet_Transmit; //設置為發送模式
delay(3000); //延時3m秒

}//for
} //if
_EINT();

}//__interrupt