25045操作標準子程序

/*;*******************************************************
*
;* Name: BYTE_WRITE
;* Description: Single Byte Write
;* Function: This routine sends the command to write a single byte to the EEPROM memory
array
;* Calls: outbyt, wip_poll
;* Input: None
;* Outputs: None
;* Register Usage: A, B
;**********************************************************
*/
/*字節寫入,aa為寫入的數據,dd為寫入的地址,對于25045而言為000-1FF*/
void byte_write(aa,dd)
uchar aa;
uint dd;
{
SCK=0;
CS=0;
outbyt((((uchar)(dd-0XFF))3)|WRITE_INST);/* Send WRITE instruction including MSB of address */
/*將高位地址左移3位與寫入先導字相或,得到正確的先導字寫入25045*/
outbyt((uchar)(dd));
/*輸出低位地址到25045*/
outbyt(aa);
/*寫入數據到25045的對應單元*/
SCK=0;
CS=1;
wip_poll();
/*檢測是否寫完*/
}

/*;********************************************************
*
;* Name: BYTE_READ
;* Description: Single Byte Read
;* Function: This routine sends the command to read a single byte from the EEPROM memory
array
;* Calls: outbyt, inputbyt
;* Input: None
;* Outputs: A = read byte
;* Register Usage: A, BXicor Application Note AN21
;********************************************************
*/
/*字節讀出,其中dd為讀出的地址,返回的值為讀出的數據*/
uchar byte_read(dd)
uint dd;
{
uchar cc;
SCK=0;
CS=0;
outbyt((((uchar)(dd-0XFF))3)|READ_INST);/* Send READ_INST instruction including MSB of address */
/*將高位地址左移3位與讀出先導字相或,得到正確的先導字寫入25045*/
outbyt((uchar)(dd));
/*輸出低位地址到25045*/
cc=inputbyt();/*得到讀出的數據*/
SCK=0;
CS=1;
return cc;
}

/*;**********************************************
*
;* Name: PAGE_WRITE
;* Description: Page Write
;* Function: This routine sends the command to write three consecutive bytes to the EEPROM
;* memory array using page mode
;* Calls: outbyt, wip_poll
;* Input: None
;* Outputs: None
;* Register Usage: A, B
;*****************************************************
*/
/*頁面寫入,其中aa1,aa2,aa3,aa4為需要寫入的4個數據(最大也就只能一次寫入4個字,dd為寫入的首地址*/
void page_write(aa1,aa2,aa3,aa4,dd)
uchar aa1,aa2,aa3,aa4;
uint dd;
{
SCK=0;
CS=0;
outbyt((((uchar)(dd-0XFF))3)|WRITE_INST);/* Send WRITE instruction including MSB of address */
/*將高位地址左移3位與寫入先導字相或,得到正確的先導字寫入25045*/
outbyt((uchar)(dd));
/*寫入低位地址到25045*/
outbyt(aa1);
/*寫入數據1到25045的對應單元*/
outbyt(aa2);
/*寫入數據2到25045的對應單元*/
outbyt(aa3);
/*寫入數據3到25045的對應單元*/
outbyt(aa4);
/*寫入數據4到25045的對應單元*/
SCK=0;
CS=1;
wip_poll();
}

/*;********************************************
*
;* Name: SEQU_READ
;* Description: Sequential Read
;* Function: This routine sends the command to read three consecutive bytes from the EEPROM
;* memory array using sequential mode
;* Calls: outbyt, inputbyt
;* Input: None
;* Outputs: A = last byte read
;* Register Usage: A, B
;*********************************************************
*/
/*連續讀出,由于函數的返回值只能為1個,對于連續讀出的數據只能使用指針作為函數的返回值才能做到返回一系列的數組*/
/*sequ_read:*/
unsigned int *page_read(n,dd)
uchar n;/*n是希望讀出的數據的個數，n=11*/
unsigned int dd;/*dd是讀出數據的首地址*/
{
uchar i;
uchar pp[10];
unsigned int *pt=pp;
SCK=0;
CS=0;
outbyt((((uchar)(dd-0XFF))3)|READ_INST);
for (i=0;in;i++)
{
pp[i]=inputbyt();
}
return (pt);
}
/*調用的方法如下*/
/*unsigned int *p;*/
/*p=page_read(4,100);*/
/*a=*(p)*/
/*b=*(p+1)*/
/*c=*(p+2)*/
/*d=*(p+3)*/
/*abcd中存放25045中由100地址開始的4個數據*/
/* Send WRITE */
/*mov DPTR, #PAGE_ADDR ; Set address of 1st byte to be read
clr sck ; Bring SCK low
clr cs ; Bring /CS low
mov A, #READ_INST
mov B, DPH
mov C, B.0
mov ACC.3, C
lcall outbyt ; Send READ instruction with MSB of address
mov A, DPL
lcall outbyt ; Send low order address byte
lcall inputbyt ; Read 1st data byte
lcall inputbyt ; Read 2nd data byte
lcall inputbyt ; Read 3rd data byte
clr sck ; Bring SCK low
setb cs ; Bring /CS high